System Configuration

by

Having kernel hung_task_timeout_secs Issues

There is a good article Linux Kernel panic issue: How to fix hung_task_timeout_secs and blocked for more than 120 seconds problem which provides an explanation and solution to kernel hung_task_timeout_secs Issues.

By default Linux uses up to 40% of the available memory for file system caching. After this mark has been reached the file system flushes all outstanding data to disk causing all following IOs going synchronous. For flushing out this data to disk this there is a time limit of 120 seconds by default. In the case here the IO subsystem is not fast enough to flush the data withing 120 seconds. As IO subsystem responds slowly and more requests are served, System Memory gets filled up resulting in the above error, thus serving HTTP requests.

Linux Kernel panic issue: How to fix hung_task_timeout_secs and blocked for more than 120 seconds problem

Resolution

Change vm.dirty_ratio and vm.dirty_backgroud_ratio

# sysctl -w vm.dirty_ratio=10
# sysctl -w vm.dirty_background_ratio=5
# sysctl -p

If you wish to make it permanent, add the 2 lines to /etc/sysctl.conf

vm.dirty_background_ratio = 5
vm.dirty_ratio = 10
by

Tools to Show your System Configuration

Tool 1: Display Information about CPU Architecture

[user1@node1 ~]$ lscpu
Architecture: x86_64
CPU op-mode(s): 32-bit, 64-bit
Byte Order: Little Endian
CPU(s): 32
On-line CPU(s) list: 0-31
Thread(s) per core: 2
Core(s) per socket: 8
Socket(s): 2
NUMA node(s): 2
Vendor ID: GenuineIntel
CPU family: 6
Model: 85
Model name: Intel(R) Xeon(R) Gold 6134 CPU @ 3.20GHz
Stepping: 4
CPU MHz: 3200.000
BogoMIPS: 6400.00
Virtualization: VT-x
L1d cache: 32K
L1i cache: 32K
L2 cache: 1024K
L3 cache: 25344K
NUMA node0 CPU(s): 0-7,16-23
NUMA node1 CPU(s): 8-15,24-31
.....
.....

Tool 2: List all PCI devices

[user1@node1 ~]# lspci -t -vv
-+-[0000:d7]-+-00.0-[d8]--
| +-01.0-[d9]--
| +-02.0-[da]--
| +-03.0-[db]--
| +-05.0 Intel Corporation Device 2034
| +-05.2 Intel Corporation Sky Lake-E RAS Configuration Registers
| +-05.4 Intel Corporation Device 2036
| +-0e.0 Intel Corporation Device 2058
| +-0e.1 Intel Corporation Device 2059
| +-0f.0 Intel Corporation Device 2058
| +-0f.1 Intel Corporation Device 2059
| +-10.0 Intel Corporation Device 2058
| +-10.1 Intel Corporation Device 2059
| +-12.0 Intel Corporation Sky Lake-E M3KTI Registers
| +-12.1 Intel Corporation Sky Lake-E M3KTI Registers
| +-12.2 Intel Corporation Sky Lake-E M3KTI Registers
| +-12.4 Intel Corporation Sky Lake-E M3KTI Registers
| +-12.5 Intel Corporation Sky Lake-E M3KTI Registers
| +-15.0 Intel Corporation Sky Lake-E M2PCI Registers
| +-16.0 Intel Corporation Sky Lake-E M2PCI Registers
| +-16.4 Intel Corporation Sky Lake-E M2PCI Registers
| \-17.0 Intel Corporation Sky Lake-E M2PCI Registers
.....
.....

Tool 3: List all PCI devices

[user@node1 ~]# lsblk
sda 8:0 0 1.1T 0 disk
├─sda1 8:1 0 200M 0 part /boot/efi
├─sda2 8:2 0 1G 0 part /boot
└─sda3 8:3 0 1.1T 0 part
├─centos-root 253:0 0 50G 0 lvm /
├─centos-swap 253:1 0 4G 0 lvm [SWAP]
└─centos-home 253:2 0 1T 0 lvm

Tool 4: See flags kernel booted with

[user@node1 ~]
BOOT_IMAGE=/vmlinuz-3.10.0-693.el7.x86_64 root=/dev/mapper/centos-root ro crashkernel=auto rd.lvm.lv=centos/root rd.lvm.lv=centos/swap rhgb quiet LANG=en_US.UTF-8

Tool 5: Display available network interfaces

[root@hpc-gekko1 ~]# ifconfig -a
eno1: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether XX:XX:XX:XX:XX:XX txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
.....
.....
.....

Tool 6 Using dmidecode to find hardware information
See Using dmidecode to find hardware information